# Artwork for Bottle and Tumbler Printing: Wrap Size, Taper and Seams

> A round object needs flat artwork that wraps exactly once. How to work out the size, handle tapers and shoulders, and send a file the printer can use.

Published 12 November 2026 by VKTR · 8 min read · https://www.vktrstudio.com/insights/bottle-tumbler-wrap-artwork

## Key takeaways

- Artwork for a round object is a flat strip: as wide as the circumference of the printed band (π × diameter) and as tall as the band.
- A tapered tumbler or cup unrolls into an arc, not a rectangle. Wraps, transfers and labels need that arc; a direct 360° printer usually maps flat artwork onto the taper in its own software.
- Measure the real item. Shoulders, seams, handles and embossing limit the printable band.
- Keep logos and text as vector shapes so they stay sharp at the final size. [VKTR Studio](https://www.vktrstudio.com/studio) exports at a width you set in millimetres.

**Artwork for printing around a bottle or tumbler is a flat rectangle as wide as the circumference of the printed band (π × the diameter) and as tall as the band you want to print.** For a straight 70 mm tumbler that is about 220 mm wide. A tapered tumbler unrolls into a curved arc instead, which matters when you print a wrap, a transfer or a label rather than printing directly on the object.

This guide gives the measurements and formulas, and explains what changes between direct 360° printing, as used for perfume and beverage bottles, and wraps applied by hand, such as sublimation and vinyl.

## Measure the printable band, not the whole bottle

Start with the real object, not a catalogue drawing. Measure:

- **The diameter** of the area you will print, with callipers if you have them. With only a tape, measure the circumference and divide it by π (3.1416).
- **The height of the straight section,** from where the body stops curving at the base to where the shoulder starts.
- **The top and bottom diameters** of that section. A difference of even a few millimetres means a taper.
- **Anything that breaks the surface:** a mould seam, a handle, embossed text, a label panel, the thread at the neck.

[Sun Studio](https://www.sunstudio.ae/services/cylindrical-printing-dubai/), a UV printing studio in Dubai in the same group as VKTR that prints 360° around bottles, cans and tumblers, asks for exactly these before quoting: front and side photos showing the profile and shoulder, the diameter, height and capacity, the material, and whether the item is straight or tapered. Its bottle printing page notes that on tapered, shouldered or oval containers the printable band has to be defined deliberately, usually over the straightest part of the body.

## Straight bottles and tumblers: a rectangle

For a straight-sided item, the artwork is a rectangle:

- **Width = π × diameter.** A 66 mm can: 207.3 mm. A 75 mm bottle: 235.6 mm.
- **Height = the printable band,** for example 120 mm on a straight tumbler.
- **Bleed, if the printer asks,** so a background colour runs past the edges. Keep text and logos well inside.

Set the document to that size in millimetres before placing any artwork. Designing on an A4 page and scaling it later is how logos end up stretched.

## Tapered tumblers and cups: an arc

A tapered item is a slice of a cone. Rolled out flat, its surface is a slice of a ring: an arc with an inner and an outer radius. A rectangle wrapped around a cone slants and leaves a gap, which is why sublimation and vinyl wraps for tapered tumblers use curved templates. A rectangle based on the average diameter is only a planning estimate for straight or lightly tapered cups.

With **D** the top (wider) diameter, **d** the bottom diameter and **h** the straight height of the band:

- **Slant height:** s = √(h² + ((D − d) ÷ 2)²)
- **Outer radius:** R = s × D ÷ (D − d)
- **Inner radius:** r = s × d ÷ (D − d), which is R − s
- **Arc angle:** 180° × (D − d) ÷ s

Worked example: a cup 90 mm across the top and 70 mm at the bottom, with a 110 mm band. The slant height is √(110² + 10²) = 110.5 mm. The outer radius is 110.5 × 90 ÷ 20 = 497.0 mm, the inner radius is 386.6 mm, and the angle is 180 × 20 ÷ 110.5 = 32.6°. The outer edge of the arc is then 282.7 mm long, the same as the circumference at the top (π × 90).

Free template tools such as the [Made Good Designs mug template](https://madegooddesigns.com/tools/mug-template/) calculate the arc from your measurements and bend the artwork into it. Whatever you use, print a paper test and wrap it around the real item before printing the final.

## Direct 360° printing works differently

Direct-to-object UV printers print onto the bottle as it turns, so there is no wrap to apply and no arc to cut. LSINC’s Peri printers, for example, print in a helical pattern on cylindrical and tapered items. Roland DG’s datasheet for the LSINC PeriQ360 lists item diameters from 38 mm to 114 mm and a maximum taper angle of +10° / −2°. Every machine has its own limits, so check them with the printer.

For these presses, artwork is normally supplied flat. Sun Studio describes it as a flat strip whose width matches the circumference of the printed band. Do not bend the artwork into an arc unless the printer asks you to; ask which size and which diameter they want it at.

Sun Studio’s page also notes that its 360° print has no start-stop line or label edge, but that handles, threads, moulding ridges, seams and embossed logos can still interrupt the surface. For a continuous pattern, make sure the left and right edges of the artwork meet cleanly, because they will touch on the bottle.

## Place the design where people will see it

- **Mark the front.** Tell the printer where the front of the item is, for example opposite the mould seam or in line with the pump. A logo placed across a seam looks broken.
- **Remember the curve.** You can never see more than half of a round object at once, and the edges of that half are seen at a steep angle. Keep the logo within the front of the wrap.
- **Expect circles to look oval near the edges.** Shapes seen at an angle look squeezed, a well-known problem when engraving tumblers. Keep key shapes near the front centre.
- **Stay clear of the shoulder and base curves.** Artwork that runs onto a curve stretches or misses.

## White ink, varnish and clear bottles

On clear glass, coloured glass and metal, colours need white underneath to look solid. Sun Studio’s bottle page says white is printed under the artwork so colour holds on clear, coloured or metallic bodies, and asks customers to flag elements that must stay opaque. [How to prepare a white ink layer](https://www.vktrstudio.com/insights/white-ink-layer) explains the setup, and the same mask method gives you selective gloss or matt varnish: see [spot UV file setup](https://www.vktrstudio.com/insights/spot-uv-file-setup).

Perfume bottles add one more concern: alcohol. Sun Studio’s guide to [alcohol-resistant perfume bottle printing](https://www.sunstudio.ae/insights/alcohol-resistant-perfume-bottle-printing-dubai/) notes that fragrance reaches a bottle on the filling line, on the counter and in the hand. The studio tests by printing a sample on the customer’s own bottle and rubbing it with the customer’s own fragrance, because each formula behaves differently. Plan for that test before a production run.

## Logos and text: keep them vector

A wrap is often 200 to 300 mm wide. A logo saved from a website at 400 pixels across will look soft at that size. Keep logos and text as vector shapes, and use raster images only for photos and painterly artwork, at full size and resolution.

If the logo only exists as a PNG or JPG, trace it in [VKTR Studio](https://www.vktrstudio.com/studio), compare the shapes with the original, and download an SVG or PDF at the width you need in millimetres. Place it into the wrap document at that size. Traced text becomes outlines, which is what printers want, but check small lettering closely. For photographs, keep the original file: a traced photo becomes stylised flat colour, not a photo. [Logo file types](https://www.vktrstudio.com/insights/logo-file-types) explains which file to keep for what.

## From measurements to file, step by step

### 1. Measure the item

Measure the diameter (or the circumference), the height of the band you want to print, the top and bottom diameters of that band, and anything that interrupts the surface.

### 2. Work out the artwork size

For a straight item, the artwork is π × diameter wide and as tall as the band. For a tapered item and a wrap, transfer or label, use the arc from the formulas above. For a direct 360° printer, use the size the printer gives you.

### 3. Set up the document in millimetres

Create the page at the final size, mark the front centre with a guide, and add bleed if the printer asks for it.

### 4. Place vector artwork

Place the vector master of the logo and the text. If you only have a PNG or JPG, trace it in [VKTR Studio](https://www.vktrstudio.com/studio) and download an SVG or PDF at the width you need in millimetres.

### 5. Mark white, varnish and the front

Put white ink and varnish on their own layers, and tell the printer where the front of the item is, for example opposite the mould seam.

### 6. Proof on the real item

Wrap a paper print around the item to check the fit, then approve a printed sample before a full run.

## Bottle and tumbler artwork: questions and answers

### How do I work out the wrap size for a tumbler?

Width = π × the diameter of the printed area; height = the printable band. For a straight 75 mm tumbler that is 235.6 mm wide. For a tapered tumbler, use an arc template calculated from the top and bottom diameters and the height.

### Why does my tumbler wrap not line up?

The tumbler is probably tapered. A rectangle wrapped around a cone slants and leaves a gap. Use a curved template made from the top and bottom diameters and the height.

### What file should I send for bottle printing?

Flat artwork at the size the printer gives you, with logos and text as vector (PDF or SVG, text converted to outlines), photos as high-resolution images, and white ink or varnish areas marked.

### Can you print all the way around a bottle?

Yes, on a cylindrical or 360° printer. The usable band is set by the straight part of the body; shoulders, handles and seams limit it.

### Do I need white ink on a clear bottle?

For colours that look solid, yes, under the elements that should be opaque. Without white, colours on clear glass read as a tint.

## Logo too small for the wrap? Trace it to vector.

Trace a PNG or JPG in VKTR Studio, set the width in millimetres and download SVG or PDF for your bottle or tumbler artwork. Converting is free; a free account downloads 2 files a day.

[Open VKTR Studio](https://www.vktrstudio.com/studio)

## References

- [Sun Studio: Bottle printing in Dubai, 360° cylindrical UV printing](https://www.sunstudio.ae/services/cylindrical-printing-dubai/)
- [Sun Studio: Alcohol-resistant perfume bottle printing](https://www.sunstudio.ae/insights/alcohol-resistant-perfume-bottle-printing-dubai/)
- [Roland DG: LSINC PeriQ360 datasheet (PDF)](https://image.rolanddg.com/-/media/roland-apac/mea/brochure/datasheet_lsinc_periq360_gw.pdf)
- [Made Good Designs: Mug and tumbler template](https://madegooddesigns.com/tools/mug-template/)
- [raw.org: Cone and frustum template generator](https://raw.org/fab/templates/printable-cone-template-generator/)
- [Bulk Tumblers: Adjusting circles on a cylinder](https://bulktumblers.com/blogs/laser-tips-and-tricks/visual-distortion-calculator-adjusting-circles-on-a-cylinder)
